Pertronix Ignitor 1544 Manual do Utilizador descarregar pdf

12-Volt Negative Ground Installation Instructions

Page 1 of 4

CAUTION!!! Before installing, please read the following important information....

909-599-5955 www.pertronix.com

12-Volt Negative Ground Installation Instructions

Page 1 of 4

CAUTION!!! Before installing, please read the following important information....

909-599-5955 www.pertronix.com

1. The Ignitor is designed for 12-Volt negative ground systems.

2. Leaving the ignition “ON” with the engine “OFF” for an extended period could result in permanent damage to

the Ignitor.

3. See Chart on back page for coil recommendations.

4. Four & Six cylinder engines require a minimum of 3.0 ohms of primary resistance. Do not remove resistors if

the coil primary resistance is less than 3.0 ohms.

5. If your Ignition coil has the recommended primary resistance, remove or bypass all external resistors.

6. The Ignitor is compatible as a trigger for most electronic boxes.

12-Volt Negative Ground Installation Instructions

Page 1 of 4

For Part Number: 1544

DISASSEMBLY

1. PRIOR TO INSTALLATION TURN IGNITION SWITCH OFF OR DISCONNECT THE BATTERY

2. Remove the distributor cap, and rotor. Do not disconnect spark plug wires. Examine cap and rotor for wear

or damage. Replace as needed.

3. Disconnect the point wire from the negative (-) terminal of the coil.

4. Remove the point wire, point, and condenser from the distributor. The Ignitor does not require any

modification to the distributor. Therefore the point, condenser and hardware can be used as backup.

5. Clean all dirt and excess oil from the breaker plate and point cam.

IGNITOR INSTALLATION

1. Position the Ignitor over point pivot pin, align Ignitor plate to breaker plate screw hole. See figure 1.

2. Confirm that the Ignitor plate is flat and fits without modifications.

3. Fasten the plate into place using the provided screw.

4. Insert wires through the wire exit hole in distributor housing. Pull the rubber grommet into place. Make sure

wires do not interfere with any moving parts.

5. The magnet sleeve has green tape, DO NOT REMOVE IT!

6. Install magnet sleeve over the distributor shaft, onto point cam. Rotate the sleeve until a slight locating

position is felt before applying pressure. Press down firmly insuring sleeve is fully seated.

7. Module and magnet sleeve air gap is not adjustable.

8. Reinstall the rotor, and the distributor cap. Make sure all spark plug wires are securely attached.

9. See Wiring Instructions.

Ignitor wires exit hole

Figure 1

1 2 3 4

Resumo do Conteúdo

Página 1 - For Part Number: 1544

12-Volt Negative Ground Installation InstructionsPage 1 of 4CAUTION!!! Before installing, please read the following important information...909-599-5

Página 2 - (FIGURE B)

COIL WIRERED WIREBLACK WIRETO IGNITION COIL WIRETO IGNITION SWITCHRED WIREBLACK WIRERESISTANCE WIREBALLAST RESISTORThe Ignitor can also be installed i

Página 3 - POWER & GROUND TESTS

Q. What is the first thing I should check if the engine would not start? A. Make certain all wires are connected securely to the proper terminals.Q. T

Página 4 - Page 4 of 4

LIMITED WARRANTY Pertronix, Inc. Warrants to the original Purchaser of its solid-state ignition system (product) that the Ignitor, magnet assembly an

Comentários a estes Manuais

Sem comentários

Pertronix Ignitor 1544 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Para o carro Pertronix Ignitor 1544. PerTronix Ignitor 1544 User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Para o carro Pertronix Ignitor 1544